|
Hello
[ 0.000000] Linux version 5.19.0-rc4 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Wed Aug 24 14:46:22 UTC 2022
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Ventana VT1 QEMU
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10001
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] SBI SRST extension detected
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: EFI v2.90 by Das U-Boot
[ 0.000000] efi: RTPROP=0xfe73c020 SMBIOS=0xfe738000 MEMRESERVE=0xfd3ca020
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fe737fff]
[ 0.000000] node 0: [mem 0x00000000fe738000-0x00000000fe738fff]
[ 0.000000] node 0: [mem 0x00000000fe739000-0x00000000fe73bfff]
[ 0.000000] node 0: [mem 0x00000000fe73c000-0x00000000fe742fff]
[ 0.000000] node 0: [mem 0x00000000fe743000-0x00000000fff77fff]
[ 0.000000] node 0: [mem 0x00000000fff78000-0x00000000fff78fff]
[ 0.000000] node 0: [mem 0x00000000fff79000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] SBI HSM extension detected
[ 0.000000] riscv: base ISA extensions acdfhim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] riscv: Svinval extension supported
[ 0.000000] percpu: Embedded 18 pages/cpu s34488 r8192 d31048 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] fixmap : 0xff1bfffffee00000 - 0xff1bffffff000000 (2048 kB)
[ 0.000000] pci io : 0xff1bffffff000000 - 0xff1c000000000000 ( 16 MB)
[ 0.000000] vmemmap : 0xff1c000000000000 - 0xff20000000000000 (1024 TB)
[ 0.000000] vmalloc : 0xff20000000000000 - 0xff60000000000000 (16384 TB)
[ 0.000000] lowmem : 0xff60000000000000 - 0xff60000080000000 (2048 MB)
[ 0.000000] kernel : 0xffffffff80000000 - 0xffffffffffffffff (2047 MB)
[ 0.000000] Memory: 2034884K/2097152K available (7677K kernel code, 4908K rwdata, 4096K rodata, 2204K init, 463K bss, 62268K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped using AIA
[ 0.000000] riscv-imsic: imsics@28000000: hart-index-bits: 4, guest-index-bits: 3
[ 0.000000] riscv-imsic: imsics@28000000: group-index-bits: 0, group-index-shift: 24
[ 0.000000] riscv-imsic: imsics@28000000: mapped 255 interrupts for 16 CPUs at 0x0000000028000000
[ 0.000000] riscv-imsic: imsics@28000000: enable/disable sync using interrupt 2
[ 0.000000] riscv-imsic: imsics@28000000: providing IPIs using interrupt 1
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [15]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000175] sched_clock: 64 bits at 10MHz, resolution 100ns, wraps every 4398046511100ns
[ 0.003481] Timer interrupt in S-mode is available via sstc extension
[ 0.025738] Console: colour dummy device 80x25
[ 0.029321] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=40000)
[ 0.031650] pid_max: default: 32768 minimum: 301
[ 0.034091] LSM: Security Framework initializing
[ 0.040644] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.041871] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.113999] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.115760] cblist_init_generic: Setting shift to 4 and lim to 1.
[ 0.118488] riscv: ELF compat mode supported
[ 0.118927] ASID allocator using 16 bits (65536 entries)
[ 0.122786] rcu: Hierarchical SRCU implementation.
[ 0.128655] Remapping and enabling EFI services.
[ 0.138132] smp: Bringing up secondary CPUs ...
[ 0.289674] smp: Brought up 1 node, 16 CPUs
[ 0.370978] devtmpfs: initialized
[ 0.384472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.385374] futex hash table entries: 4096 (order: 6, 262144 bytes, linear)
[ 0.395700] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.402142] audit: initializing netlink subsys (disabled)
[ 0.405233] audit: type=2000 audit(0.332:1): state=initialized audit_enabled=0 res=1
[ 0.409992] cpuidle: using governor menu
[ 0.991252] riscv-aplic d000000.aplic: 96 interrupts forwared to MSI base 0x0000000028000000
[ 1.023056] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 1.032106] ACPI: Interpreter disabled.
[ 1.032688] iommu: Default domain type: Translated
[ 1.033087] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.035341] SCSI subsystem initialized
[ 1.040840] usbcore: registered new interface driver usbfs
[ 1.041953] usbcore: registered new interface driver hub
[ 1.042680] usbcore: registered new device driver usb
[ 1.044787] Registered efivars operations
[ 1.066789] vgaarb: loaded
[ 1.070677] clocksource: Switched to clocksource riscv_clocksource
[ 1.074619] pnp: PnP ACPI: disabled
[ 1.116227] NET: Registered PF_INET protocol family
[ 1.126621] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.137534] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 1.138660] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.139011] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.139754] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 1.141266] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.144634] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.145365] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.148897] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.159051] RPC: Registered named UNIX socket transport module.
[ 1.159353] RPC: Registered udp transport module.
[ 1.159522] RPC: Registered tcp transport module.
[ 1.159699] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.176066] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.213547] NFS: Registering the id_resolver key type
[ 1.216026] Key type id_resolver registered
[ 1.216360] Key type id_legacy registered
[ 1.217343] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.217841] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.220266] 9p: Installing v9fs 9p2000 file system support
[ 1.224198] NET: Registered PF_ALG protocol family
[ 1.225340] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.227416] io scheduler mq-deadline registered
[ 1.227748] io scheduler kyber registered
[ 1.249381] pci-host-generic 30000000.pci: host bridge /soc/pci@30000000 ranges:
[ 1.251169] pci-host-generic 30000000.pci: IO 0x0003000000..0x000300ffff -> 0x0000000000
[ 1.252302] pci-host-generic 30000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
[ 1.252770] pci-host-generic 30000000.pci: MEM 0x0400000000..0x07ffffffff -> 0x0400000000
[ 1.254245] pci-host-generic 30000000.pci: Memory resource size exceeds max for 32 bits
[ 1.260809] pci-host-generic 30000000.pci: ECAM at [mem 0x30000000-0x3fffffff] for [bus 00-ff]
[ 1.264633] pci-host-generic 30000000.pci: PCI host bridge to bus 0000:00
[ 1.265205] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.265504] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.265799] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 1.266707] pci_bus 0000:00: root bus resource [mem 0x400000000-0x7ffffffff]
[ 1.268627] pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.810913] loop: module loaded
[ 1.813333] virtio_blk virtio1: 1/0/0 default/read/poll queues
[ 1.825357] virtio_blk virtio1: [vda] 1071932 512-byte logical blocks (549 MB/523 MiB)
[ 1.909650] vda: vda1 vda2 vda3
[ 1.942916] tun: Universal TUN/TAP device driver, 1.6
[ 1.964238] e1000: Intel(R) PRO/1000 Network Driver
[ 1.964596] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.965214] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.965496] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.967174] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.967691] ehci-pci: EHCI PCI platform driver
[ 1.968378] ehci-platform: EHCI generic platform driver
[ 1.969031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.969540] ohci-pci: OHCI PCI platform driver
[ 1.970742] ohci-platform: OHCI generic platform driver
[ 1.974710] usbcore: registered new interface driver uas
[ 1.975701] usbcore: registered new interface driver usb-storage
[ 1.979125] mousedev: PS/2 mouse device common for all mice
[ 1.985774] goldfish_rtc 101000.rtc: registered as rtc0
[ 1.987831] goldfish_rtc 101000.rtc: setting system clock to 2022-08-25T10:45:53 UTC (1661424353)
[ 1.993669] syscon-poweroff soc:poweroff: pm_power_off already claimed for sbi_srst_power_off
[ 1.995212] syscon-poweroff: probe of soc:poweroff failed with error -16
[ 1.998593] sdhci: Secure Digital Host Controller Interface driver
[ 1.998909] sdhci: Copyright(c) Pierre Ossman
[ 1.999509] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.001283] usbcore: registered new interface driver usbhid
[ 2.001588] usbhid: USB HID core driver
[ 2.002927] riscv-pmu-sbi: SBI PMU extension is available
[ 2.004257] riscv-pmu-sbi: 16 firmware and 18 hardware counters
[ 2.017615] NET: Registered PF_INET6 protocol family
[ 2.032397] Segment Routing with IPv6
[ 2.032878] In-situ OAM (IOAM) with IPv6
[ 2.033574] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.037639] NET: Registered PF_PACKET protocol family
[ 2.039420] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.040579] 8021q: 802.1Q VLAN Support v1.8
[ 2.043124] 9pnet: Installing 9P2000 support
[ 2.043788] Key type dns_resolver registered
[ 2.050694] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 2.145175] EXT4-fs (vda2): mounted filesystem with ordered data mode. Quota mode: disabled.
[ 2.146407] VFS: Mounted root (ext4 filesystem) readonly on device 254:2.
[ 2.150622] devtmpfs: mounted
[ 2.201842] Freeing unused kernel image (initmem) memory: 2204K
[ 2.228413] Run /sbin/init as init process
[ 2.242343] Run /etc/init as init process
[ 2.243725] Run /bin/init as init process
[ 2.244949] Run /bin/sh as init process
sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-5.1#
sh-5.1#
sh-5.1# QEMU: Terminated
Thank you.
Regards
Vaibhav Vivek Deshpande
|
|
|
Interesting... Looking into the log massage itself! [ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000 Command line does not specify baud rate... Usually by default it is 115200. Just a kludge. Then: [ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled bootconsole enabled, seems correct. Then: [ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled From what we see that the base baud rate is 230400 (?), everything else is, seems, correct. So, three things, which came adhoc to my mind: [1] Please, check the baud rate; [2] Please, check to which group /dev/ttyS0 belongs (root dialout)? [3] The terminal should be interactive, but no way to check this (from the logs)??? My two cent worth answer, Zee _______ On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande <vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
...[snap]...
|
|
|
Helo
I have added systemd in rootfs by adding IMAGE_INSTALL = " systemd" in local.conf and the issue solved is this required for the latest yocto version (kirkstone)?
Thank you.
Regards
Vaibhav Vivek Deshpande
Interesting... Looking into the log massage itself!
> [ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
Command line does not specify baud rate... Usually by default it is
115200. Just a kludge.
Then:
> [ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
> [ 0.000000] printk: bootconsole [uart8250] enabled
bootconsole enabled, seems correct.
Then:
> [ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
> [ 1.648238] printk: console [ttyS0] disabled
> [ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
> [ 1.656816] printk: console [ttyS0] enabled
> [ 1.656816] printk: console [ttyS0] enabled
> [ 1.657728] printk: bootconsole [uart8250] disabled
> [ 1.657728] printk: bootconsole [uart8250] disabled
From what we see that the base baud rate is 230400 (?), everything
else is, seems, correct.
So, three things, which came adhoc to my mind:
[1] Please, check the baud rate;
[2] Please, check to which group /dev/ttyS0 belongs (root dialout)?
[3] The terminal should be interactive, but no way to check this (from
the logs)???
My two cent worth answer,
Zee
_______
On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande
<vdeshpande@...> wrote:
>
> Hello
>
> I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
...[snap]...
|
|
|
Hi Vaibhav, Out of curiosity which image did you build? Kind regards, Laurent. On Thu, Oct 20, 2022 at 7:07 PM Vaibhav Deshpande <vdeshpande@...> wrote:
Helo
I have added systemd in rootfs by adding IMAGE_INSTALL = " systemd" in local.conf and the issue solved
is this required for the latest yocto version (kirkstone)?
Thank you.
Regards
Vaibhav Vivek Deshpande
On Mon, Oct 17, 2022 at 1:28 AM Zoran Stojsavljevic <zoran.stojsavljevic@...> wrote:
Interesting... Looking into the log massage itself!
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000 Command line does not specify baud rate... Usually by default it is
115200. Just a kludge.
Then:
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled bootconsole enabled, seems correct.
Then:
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled From what we see that the base baud rate is 230400 (?), everything
else is, seems, correct.
So, three things, which came adhoc to my mind:
[1] Please, check the baud rate;
[2] Please, check to which group /dev/ttyS0 belongs (root dialout)?
[3] The terminal should be interactive, but no way to check this (from
the logs)???
My two cent worth answer,
Zee
_______
On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande
<vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
...[snap]...
-- Laurent Gauthier Embedded Linux Systems & Software Phone: +33 630 483 429 https://soccasys.com
|
|
|
I have added systemd in rootfs by adding
MAGE_INSTALL = " systemd" in local.conf
and the issue solved is this required for the
latest yocto version (kirkstone)? You did set the INIT_MANAGER ?= "systemd", didn't you? And how (in which manner) systemd influences the console, or consoles setup? Consoles' setup should be done much earlier then systemd!? Zee _______ On Thu, Oct 20, 2022 at 7:07 PM Vaibhav Deshpande <vdeshpande@...> wrote:
Helo
I have added systemd in rootfs by adding IMAGE_INSTALL = " systemd" in local.conf and the issue solved
is this required for the latest yocto version (kirkstone)?
Thank you.
Regards
Vaibhav Vivek Deshpande
On Mon, Oct 17, 2022 at 1:28 AM Zoran Stojsavljevic <zoran.stojsavljevic@...> wrote:
Interesting... Looking into the log massage itself!
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000 Command line does not specify baud rate... Usually by default it is
115200. Just a kludge.
Then:
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled bootconsole enabled, seems correct.
Then:
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled From what we see that the base baud rate is 230400 (?), everything
else is, seems, correct.
So, three things, which came adhoc to my mind:
[1] Please, check the baud rate;
[2] Please, check to which group /dev/ttyS0 belongs (root dialout)?
[3] The terminal should be interactive, but no way to check this (from
the logs)???
My two cent worth answer,
Zee
_______
On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande
<vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
...[snap]...
|
|
|
Hello Zoran
Yes, i have set INIT_MANAGER ?= "systemd"
it does not related to console but init
Failure logs : -
sh-5.1# ls -l /sbin/init
ls: cannot access '/sbin/init': No such file or directory
sh-5.1# ls -l /lib/systemd/
total 8
drwxr-xr-x 2 root root 4096 Mar 9 2018 system
drwxr-xr-x 2 root root 4096 Mar 9 2018 system-preset
Working Logs (after adding IMAGE_INSTALL = " systemd") :-
root@qemuriscv64:/# ls -l /sbin/init
lrwxrwxrwx 1 root root 22 Mar 9 2018 /sbin/init -> ../lib/systemd/systemd
root@qemuriscv64:/# ls /lib/systemd/
journald.conf.d system-shutdown systemd-growfs systemd-network-generator systemd-shutdown systemd-update-done
libsystemd-shared-250.so system-sleep systemd-hibernate-resume systemd-networkd systemd-sleep systemd-update-helper
logind.conf.d system.conf.d systemd-hostnamed systemd-networkd-wait-online systemd-socket-proxyd systemd-update-utmp
network systemd systemd-initctl systemd-pstore systemd-sulogin-shell systemd-user-runtime-dir
ntp-units.d systemd-ac-power systemd-journald systemd-quotacheck systemd-sysctl systemd-user-sessions
resolv.conf systemd-backlight systemd-localed systemd-random-seed systemd-time-wait-sync systemd-userdbd
system systemd-boot-check-no-failures systemd-logind systemd-remount-fs systemd-timedated systemd-userwork
system-generators systemd-cgroups-agent systemd-makefs systemd-reply-password systemd-timesyncd systemd-vconsole-setup
system-preset systemd-fsck systemd-modules-load systemd-resolved systemd-udevd systemd-volatile-root
root@qemuriscv64:/#
Thank you
Regards
Vaibhav Vivek Deshpande
> I have added systemd in rootfs by adding
> MAGE_INSTALL = " systemd" in local.conf
> and the issue solved is this required for the
> latest yocto version (kirkstone)?
You did set the INIT_MANAGER ?= "systemd", didn't you?
And how (in which manner) systemd influences the console, or consoles setup?
Consoles' setup should be done much earlier then systemd!?
Zee
_______
On Thu, Oct 20, 2022 at 7:07 PM Vaibhav Deshpande
<vdeshpande@...> wrote:
>
> Helo
>
> I have added systemd in rootfs by adding IMAGE_INSTALL = " systemd" in local.conf and the issue solved
> is this required for the latest yocto version (kirkstone)?
>
>
> Thank you.
>
> Regards
> Vaibhav Vivek Deshpande
>
>
> On Mon, Oct 17, 2022 at 1:28 AM Zoran Stojsavljevic <zoran.stojsavljevic@...> wrote:
>>
>> Interesting... Looking into the log massage itself!
>>
>> > [ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
>>
>> Command line does not specify baud rate... Usually by default it is
>> 115200. Just a kludge.
>>
>> Then:
>>
>> > [ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
>> > [ 0.000000] printk: bootconsole [uart8250] enabled
>>
>> bootconsole enabled, seems correct.
>>
>> Then:
>>
>> > [ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>> > [ 1.648238] printk: console [ttyS0] disabled
>> > [ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
>> > [ 1.656816] printk: console [ttyS0] enabled
>> > [ 1.656816] printk: console [ttyS0] enabled
>> > [ 1.657728] printk: bootconsole [uart8250] disabled
>> > [ 1.657728] printk: bootconsole [uart8250] disabled
>>
>> From what we see that the base baud rate is 230400 (?), everything
>> else is, seems, correct.
>>
>> So, three things, which came adhoc to my mind:
>> [1] Please, check the baud rate;
>> [2] Please, check to which group /dev/ttyS0 belongs (root dialout)?
>> [3] The terminal should be interactive, but no way to check this (from
>> the logs)???
>>
>> My two cent worth answer,
>> Zee
>> _______
>>
>> On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande
>> <vdeshpande@...> wrote:
>> >
>> > Hello
>> >
>> > I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
>>
>> ...[snap]...
|
|
|
Hello Laurent
I am building for qemuriscv64
Command :-
MACHINE=qemuriscv64 bitbake core-image-full-cmdline
Thank you. Regards
Vaibhav Vivek Deshpande
Hi Vaibhav,
Out of curiosity which image did you build?
Kind regards, Laurent.
On Thu, Oct 20, 2022 at 7:07 PM Vaibhav Deshpande
<vdeshpande@...> wrote:
>
> Helo
>
> I have added systemd in rootfs by adding IMAGE_INSTALL = " systemd" in local.conf and the issue solved
> is this required for the latest yocto version (kirkstone)?
>
>
> Thank you.
>
> Regards
> Vaibhav Vivek Deshpande
>
>
> On Mon, Oct 17, 2022 at 1:28 AM Zoran Stojsavljevic <zoran.stojsavljevic@...> wrote:
>>
>> Interesting... Looking into the log massage itself!
>>
>> > [ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
>>
>> Command line does not specify baud rate... Usually by default it is
>> 115200. Just a kludge.
>>
>> Then:
>>
>> > [ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
>> > [ 0.000000] printk: bootconsole [uart8250] enabled
>>
>> bootconsole enabled, seems correct.
>>
>> Then:
>>
>> > [ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
>> > [ 1.648238] printk: console [ttyS0] disabled
>> > [ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
>> > [ 1.656816] printk: console [ttyS0] enabled
>> > [ 1.656816] printk: console [ttyS0] enabled
>> > [ 1.657728] printk: bootconsole [uart8250] disabled
>> > [ 1.657728] printk: bootconsole [uart8250] disabled
>>
>> From what we see that the base baud rate is 230400 (?), everything
>> else is, seems, correct.
>>
>> So, three things, which came adhoc to my mind:
>> [1] Please, check the baud rate;
>> [2] Please, check to which group /dev/ttyS0 belongs (root dialout)?
>> [3] The terminal should be interactive, but no way to check this (from
>> the logs)???
>>
>> My two cent worth answer,
>> Zee
>> _______
>>
>> On Sun, Oct 16, 2022 at 8:32 PM Vaibhav Deshpande
>> <vdeshpande@...> wrote:
>> >
>> > Hello
>> >
>> > I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
>>
>> ...[snap]...
>
>
>
>
--
Laurent Gauthier
Embedded Linux Systems & Software
Phone: +33 630 483 429
https://soccasys.com
|
|
|
Khem Raj
If you are using poky then ssytemd is not default init system, its sysvinit. For enabling systemd its best to start with DISTRO = "poky-altcfg" On Sun, Oct 16, 2022 at 11:32 AM Vaibhav Deshpande <vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
[ 0.000000] Linux version 5.19.0-rc4 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Wed Aug 24 14:46:22 UTC 2022
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Ventana VT1 QEMU
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10001
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] SBI SRST extension detected
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: EFI v2.90 by Das U-Boot
[ 0.000000] efi: RTPROP=0xfe73c020 SMBIOS=0xfe738000 MEMRESERVE=0xfd3ca020
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fe737fff]
[ 0.000000] node 0: [mem 0x00000000fe738000-0x00000000fe738fff]
[ 0.000000] node 0: [mem 0x00000000fe739000-0x00000000fe73bfff]
[ 0.000000] node 0: [mem 0x00000000fe73c000-0x00000000fe742fff]
[ 0.000000] node 0: [mem 0x00000000fe743000-0x00000000fff77fff]
[ 0.000000] node 0: [mem 0x00000000fff78000-0x00000000fff78fff]
[ 0.000000] node 0: [mem 0x00000000fff79000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] SBI HSM extension detected
[ 0.000000] riscv: base ISA extensions acdfhim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] riscv: Svinval extension supported
[ 0.000000] percpu: Embedded 18 pages/cpu s34488 r8192 d31048 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] fixmap : 0xff1bfffffee00000 - 0xff1bffffff000000 (2048 kB)
[ 0.000000] pci io : 0xff1bffffff000000 - 0xff1c000000000000 ( 16 MB)
[ 0.000000] vmemmap : 0xff1c000000000000 - 0xff20000000000000 (1024 TB)
[ 0.000000] vmalloc : 0xff20000000000000 - 0xff60000000000000 (16384 TB)
[ 0.000000] lowmem : 0xff60000000000000 - 0xff60000080000000 (2048 MB)
[ 0.000000] kernel : 0xffffffff80000000 - 0xffffffffffffffff (2047 MB)
[ 0.000000] Memory: 2034884K/2097152K available (7677K kernel code, 4908K rwdata, 4096K rodata, 2204K init, 463K bss, 62268K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped using AIA
[ 0.000000] riscv-imsic: imsics@28000000: hart-index-bits: 4, guest-index-bits: 3
[ 0.000000] riscv-imsic: imsics@28000000: group-index-bits: 0, group-index-shift: 24
[ 0.000000] riscv-imsic: imsics@28000000: mapped 255 interrupts for 16 CPUs at 0x0000000028000000
[ 0.000000] riscv-imsic: imsics@28000000: enable/disable sync using interrupt 2
[ 0.000000] riscv-imsic: imsics@28000000: providing IPIs using interrupt 1
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [15]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000175] sched_clock: 64 bits at 10MHz, resolution 100ns, wraps every 4398046511100ns
[ 0.003481] Timer interrupt in S-mode is available via sstc extension
[ 0.025738] Console: colour dummy device 80x25
[ 0.029321] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=40000)
[ 0.031650] pid_max: default: 32768 minimum: 301
[ 0.034091] LSM: Security Framework initializing
[ 0.040644] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.041871] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.113999] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.115760] cblist_init_generic: Setting shift to 4 and lim to 1.
[ 0.118488] riscv: ELF compat mode supported
[ 0.118927] ASID allocator using 16 bits (65536 entries)
[ 0.122786] rcu: Hierarchical SRCU implementation.
[ 0.128655] Remapping and enabling EFI services.
[ 0.138132] smp: Bringing up secondary CPUs ...
[ 0.289674] smp: Brought up 1 node, 16 CPUs
[ 0.370978] devtmpfs: initialized
[ 0.384472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.385374] futex hash table entries: 4096 (order: 6, 262144 bytes, linear)
[ 0.395700] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.402142] audit: initializing netlink subsys (disabled)
[ 0.405233] audit: type=2000 audit(0.332:1): state=initialized audit_enabled=0 res=1
[ 0.409992] cpuidle: using governor menu
[ 0.991252] riscv-aplic d000000.aplic: 96 interrupts forwared to MSI base 0x0000000028000000
[ 1.023056] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 1.032106] ACPI: Interpreter disabled.
[ 1.032688] iommu: Default domain type: Translated
[ 1.033087] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.035341] SCSI subsystem initialized
[ 1.040840] usbcore: registered new interface driver usbfs
[ 1.041953] usbcore: registered new interface driver hub
[ 1.042680] usbcore: registered new device driver usb
[ 1.044787] Registered efivars operations
[ 1.066789] vgaarb: loaded
[ 1.070677] clocksource: Switched to clocksource riscv_clocksource
[ 1.074619] pnp: PnP ACPI: disabled
[ 1.116227] NET: Registered PF_INET protocol family
[ 1.126621] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.137534] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 1.138660] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.139011] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.139754] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 1.141266] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.144634] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.145365] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.148897] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.159051] RPC: Registered named UNIX socket transport module.
[ 1.159353] RPC: Registered udp transport module.
[ 1.159522] RPC: Registered tcp transport module.
[ 1.159699] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.176066] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.213547] NFS: Registering the id_resolver key type
[ 1.216026] Key type id_resolver registered
[ 1.216360] Key type id_legacy registered
[ 1.217343] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.217841] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.220266] 9p: Installing v9fs 9p2000 file system support
[ 1.224198] NET: Registered PF_ALG protocol family
[ 1.225340] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.227416] io scheduler mq-deadline registered
[ 1.227748] io scheduler kyber registered
[ 1.249381] pci-host-generic 30000000.pci: host bridge /soc/pci@30000000 ranges:
[ 1.251169] pci-host-generic 30000000.pci: IO 0x0003000000..0x000300ffff -> 0x0000000000
[ 1.252302] pci-host-generic 30000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
[ 1.252770] pci-host-generic 30000000.pci: MEM 0x0400000000..0x07ffffffff -> 0x0400000000
[ 1.254245] pci-host-generic 30000000.pci: Memory resource size exceeds max for 32 bits
[ 1.260809] pci-host-generic 30000000.pci: ECAM at [mem 0x30000000-0x3fffffff] for [bus 00-ff]
[ 1.264633] pci-host-generic 30000000.pci: PCI host bridge to bus 0000:00
[ 1.265205] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.265504] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.265799] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 1.266707] pci_bus 0000:00: root bus resource [mem 0x400000000-0x7ffffffff]
[ 1.268627] pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.810913] loop: module loaded
[ 1.813333] virtio_blk virtio1: 1/0/0 default/read/poll queues
[ 1.825357] virtio_blk virtio1: [vda] 1071932 512-byte logical blocks (549 MB/523 MiB)
[ 1.909650] vda: vda1 vda2 vda3
[ 1.942916] tun: Universal TUN/TAP device driver, 1.6
[ 1.964238] e1000: Intel(R) PRO/1000 Network Driver
[ 1.964596] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.965214] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.965496] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.967174] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.967691] ehci-pci: EHCI PCI platform driver
[ 1.968378] ehci-platform: EHCI generic platform driver
[ 1.969031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.969540] ohci-pci: OHCI PCI platform driver
[ 1.970742] ohci-platform: OHCI generic platform driver
[ 1.974710] usbcore: registered new interface driver uas
[ 1.975701] usbcore: registered new interface driver usb-storage
[ 1.979125] mousedev: PS/2 mouse device common for all mice
[ 1.985774] goldfish_rtc 101000.rtc: registered as rtc0
[ 1.987831] goldfish_rtc 101000.rtc: setting system clock to 2022-08-25T10:45:53 UTC (1661424353)
[ 1.993669] syscon-poweroff soc:poweroff: pm_power_off already claimed for sbi_srst_power_off
[ 1.995212] syscon-poweroff: probe of soc:poweroff failed with error -16
[ 1.998593] sdhci: Secure Digital Host Controller Interface driver
[ 1.998909] sdhci: Copyright(c) Pierre Ossman
[ 1.999509] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.001283] usbcore: registered new interface driver usbhid
[ 2.001588] usbhid: USB HID core driver
[ 2.002927] riscv-pmu-sbi: SBI PMU extension is available
[ 2.004257] riscv-pmu-sbi: 16 firmware and 18 hardware counters
[ 2.017615] NET: Registered PF_INET6 protocol family
[ 2.032397] Segment Routing with IPv6
[ 2.032878] In-situ OAM (IOAM) with IPv6
[ 2.033574] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.037639] NET: Registered PF_PACKET protocol family
[ 2.039420] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.040579] 8021q: 802.1Q VLAN Support v1.8
[ 2.043124] 9pnet: Installing 9P2000 support
[ 2.043788] Key type dns_resolver registered
[ 2.050694] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 2.145175] EXT4-fs (vda2): mounted filesystem with ordered data mode. Quota mode: disabled.
[ 2.146407] VFS: Mounted root (ext4 filesystem) readonly on device 254:2.
[ 2.150622] devtmpfs: mounted
[ 2.201842] Freeing unused kernel image (initmem) memory: 2204K
[ 2.228413] Run /sbin/init as init process
[ 2.242343] Run /etc/init as init process
[ 2.243725] Run /bin/init as init process
[ 2.244949] Run /bin/sh as init process
sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-5.1#
sh-5.1#
sh-5.1# QEMU: Terminated
Thank you.
Regards
Vaibhav Vivek Deshpande
|
|
|
For enabling systemd its best to start with
DISTRO = "poky-altcfg" With all due respect, Khem, I thought that this line in local.conf makes systemd as default?! INIT_MANAGER ?= "systemd" Hello Zoran
Yes, i have set INIT_MANAGER ?= "systemd"
Zee _______ On Fri, Oct 21, 2022 at 6:28 PM Khem Raj <raj.khem@...> wrote:
If you are using poky then ssytemd is not default init system, its
sysvinit. For enabling systemd its best to start with
DISTRO = "poky-altcfg"
On Sun, Oct 16, 2022 at 11:32 AM Vaibhav Deshpande
<vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
[ 0.000000] Linux version 5.19.0-rc4 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Wed Aug 24 14:46:22 UTC 2022
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Ventana VT1 QEMU
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10001
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] SBI SRST extension detected
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: EFI v2.90 by Das U-Boot
[ 0.000000] efi: RTPROP=0xfe73c020 SMBIOS=0xfe738000 MEMRESERVE=0xfd3ca020
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fe737fff]
[ 0.000000] node 0: [mem 0x00000000fe738000-0x00000000fe738fff]
[ 0.000000] node 0: [mem 0x00000000fe739000-0x00000000fe73bfff]
[ 0.000000] node 0: [mem 0x00000000fe73c000-0x00000000fe742fff]
[ 0.000000] node 0: [mem 0x00000000fe743000-0x00000000fff77fff]
[ 0.000000] node 0: [mem 0x00000000fff78000-0x00000000fff78fff]
[ 0.000000] node 0: [mem 0x00000000fff79000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] SBI HSM extension detected
[ 0.000000] riscv: base ISA extensions acdfhim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] riscv: Svinval extension supported
[ 0.000000] percpu: Embedded 18 pages/cpu s34488 r8192 d31048 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] fixmap : 0xff1bfffffee00000 - 0xff1bffffff000000 (2048 kB)
[ 0.000000] pci io : 0xff1bffffff000000 - 0xff1c000000000000 ( 16 MB)
[ 0.000000] vmemmap : 0xff1c000000000000 - 0xff20000000000000 (1024 TB)
[ 0.000000] vmalloc : 0xff20000000000000 - 0xff60000000000000 (16384 TB)
[ 0.000000] lowmem : 0xff60000000000000 - 0xff60000080000000 (2048 MB)
[ 0.000000] kernel : 0xffffffff80000000 - 0xffffffffffffffff (2047 MB)
[ 0.000000] Memory: 2034884K/2097152K available (7677K kernel code, 4908K rwdata, 4096K rodata, 2204K init, 463K bss, 62268K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped using AIA
[ 0.000000] riscv-imsic: imsics@28000000: hart-index-bits: 4, guest-index-bits: 3
[ 0.000000] riscv-imsic: imsics@28000000: group-index-bits: 0, group-index-shift: 24
[ 0.000000] riscv-imsic: imsics@28000000: mapped 255 interrupts for 16 CPUs at 0x0000000028000000
[ 0.000000] riscv-imsic: imsics@28000000: enable/disable sync using interrupt 2
[ 0.000000] riscv-imsic: imsics@28000000: providing IPIs using interrupt 1
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [15]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000175] sched_clock: 64 bits at 10MHz, resolution 100ns, wraps every 4398046511100ns
[ 0.003481] Timer interrupt in S-mode is available via sstc extension
[ 0.025738] Console: colour dummy device 80x25
[ 0.029321] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=40000)
[ 0.031650] pid_max: default: 32768 minimum: 301
[ 0.034091] LSM: Security Framework initializing
[ 0.040644] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.041871] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.113999] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.115760] cblist_init_generic: Setting shift to 4 and lim to 1.
[ 0.118488] riscv: ELF compat mode supported
[ 0.118927] ASID allocator using 16 bits (65536 entries)
[ 0.122786] rcu: Hierarchical SRCU implementation.
[ 0.128655] Remapping and enabling EFI services.
[ 0.138132] smp: Bringing up secondary CPUs ...
[ 0.289674] smp: Brought up 1 node, 16 CPUs
[ 0.370978] devtmpfs: initialized
[ 0.384472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.385374] futex hash table entries: 4096 (order: 6, 262144 bytes, linear)
[ 0.395700] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.402142] audit: initializing netlink subsys (disabled)
[ 0.405233] audit: type=2000 audit(0.332:1): state=initialized audit_enabled=0 res=1
[ 0.409992] cpuidle: using governor menu
[ 0.991252] riscv-aplic d000000.aplic: 96 interrupts forwared to MSI base 0x0000000028000000
[ 1.023056] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 1.032106] ACPI: Interpreter disabled.
[ 1.032688] iommu: Default domain type: Translated
[ 1.033087] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.035341] SCSI subsystem initialized
[ 1.040840] usbcore: registered new interface driver usbfs
[ 1.041953] usbcore: registered new interface driver hub
[ 1.042680] usbcore: registered new device driver usb
[ 1.044787] Registered efivars operations
[ 1.066789] vgaarb: loaded
[ 1.070677] clocksource: Switched to clocksource riscv_clocksource
[ 1.074619] pnp: PnP ACPI: disabled
[ 1.116227] NET: Registered PF_INET protocol family
[ 1.126621] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.137534] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 1.138660] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.139011] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.139754] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 1.141266] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.144634] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.145365] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.148897] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.159051] RPC: Registered named UNIX socket transport module.
[ 1.159353] RPC: Registered udp transport module.
[ 1.159522] RPC: Registered tcp transport module.
[ 1.159699] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.176066] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.213547] NFS: Registering the id_resolver key type
[ 1.216026] Key type id_resolver registered
[ 1.216360] Key type id_legacy registered
[ 1.217343] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.217841] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.220266] 9p: Installing v9fs 9p2000 file system support
[ 1.224198] NET: Registered PF_ALG protocol family
[ 1.225340] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.227416] io scheduler mq-deadline registered
[ 1.227748] io scheduler kyber registered
[ 1.249381] pci-host-generic 30000000.pci: host bridge /soc/pci@30000000 ranges:
[ 1.251169] pci-host-generic 30000000.pci: IO 0x0003000000..0x000300ffff -> 0x0000000000
[ 1.252302] pci-host-generic 30000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
[ 1.252770] pci-host-generic 30000000.pci: MEM 0x0400000000..0x07ffffffff -> 0x0400000000
[ 1.254245] pci-host-generic 30000000.pci: Memory resource size exceeds max for 32 bits
[ 1.260809] pci-host-generic 30000000.pci: ECAM at [mem 0x30000000-0x3fffffff] for [bus 00-ff]
[ 1.264633] pci-host-generic 30000000.pci: PCI host bridge to bus 0000:00
[ 1.265205] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.265504] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.265799] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 1.266707] pci_bus 0000:00: root bus resource [mem 0x400000000-0x7ffffffff]
[ 1.268627] pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.810913] loop: module loaded
[ 1.813333] virtio_blk virtio1: 1/0/0 default/read/poll queues
[ 1.825357] virtio_blk virtio1: [vda] 1071932 512-byte logical blocks (549 MB/523 MiB)
[ 1.909650] vda: vda1 vda2 vda3
[ 1.942916] tun: Universal TUN/TAP device driver, 1.6
[ 1.964238] e1000: Intel(R) PRO/1000 Network Driver
[ 1.964596] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.965214] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.965496] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.967174] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.967691] ehci-pci: EHCI PCI platform driver
[ 1.968378] ehci-platform: EHCI generic platform driver
[ 1.969031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.969540] ohci-pci: OHCI PCI platform driver
[ 1.970742] ohci-platform: OHCI generic platform driver
[ 1.974710] usbcore: registered new interface driver uas
[ 1.975701] usbcore: registered new interface driver usb-storage
[ 1.979125] mousedev: PS/2 mouse device common for all mice
[ 1.985774] goldfish_rtc 101000.rtc: registered as rtc0
[ 1.987831] goldfish_rtc 101000.rtc: setting system clock to 2022-08-25T10:45:53 UTC (1661424353)
[ 1.993669] syscon-poweroff soc:poweroff: pm_power_off already claimed for sbi_srst_power_off
[ 1.995212] syscon-poweroff: probe of soc:poweroff failed with error -16
[ 1.998593] sdhci: Secure Digital Host Controller Interface driver
[ 1.998909] sdhci: Copyright(c) Pierre Ossman
[ 1.999509] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.001283] usbcore: registered new interface driver usbhid
[ 2.001588] usbhid: USB HID core driver
[ 2.002927] riscv-pmu-sbi: SBI PMU extension is available
[ 2.004257] riscv-pmu-sbi: 16 firmware and 18 hardware counters
[ 2.017615] NET: Registered PF_INET6 protocol family
[ 2.032397] Segment Routing with IPv6
[ 2.032878] In-situ OAM (IOAM) with IPv6
[ 2.033574] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.037639] NET: Registered PF_PACKET protocol family
[ 2.039420] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.040579] 8021q: 802.1Q VLAN Support v1.8
[ 2.043124] 9pnet: Installing 9P2000 support
[ 2.043788] Key type dns_resolver registered
[ 2.050694] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 2.145175] EXT4-fs (vda2): mounted filesystem with ordered data mode. Quota mode: disabled.
[ 2.146407] VFS: Mounted root (ext4 filesystem) readonly on device 254:2.
[ 2.150622] devtmpfs: mounted
[ 2.201842] Freeing unused kernel image (initmem) memory: 2204K
[ 2.228413] Run /sbin/init as init process
[ 2.242343] Run /etc/init as init process
[ 2.243725] Run /bin/init as init process
[ 2.244949] Run /bin/sh as init process
sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-5.1#
sh-5.1#
sh-5.1# QEMU: Terminated
Thank you.
Regards
Vaibhav Vivek Deshpande
|
|
|
Khem Raj
On Fri, Oct 21, 2022 at 10:38 AM Zoran Stojsavljevic <zoran.stojsavljevic@...> wrote:
For enabling systemd its best to start with
DISTRO = "poky-altcfg" With all due respect, Khem, I thought that this line in local.conf
makes systemd as default?!
INIT_MANAGER ?= "systemd"
yes that will do it. Infact thats what poky-altconfig does largely as well. see https://git.yoctoproject.org/poky/tree/meta-poky/conf/distro/poky-altcfg.conf#n11
Hello Zoran
Yes, i have set INIT_MANAGER ?= "systemd"
Zee
_______
On Fri, Oct 21, 2022 at 6:28 PM Khem Raj <raj.khem@...> wrote:
If you are using poky then ssytemd is not default init system, its
sysvinit. For enabling systemd its best to start with
DISTRO = "poky-altcfg"
On Sun, Oct 16, 2022 at 11:32 AM Vaibhav Deshpande
<vdeshpande@...> wrote:
Hello
I am trying to build a yocto image from the kirkstone branch (https://github.com/openembedded/openembedded-core/tree/kirkstone) build gets successful but at the time of linux booting I am getting below error.
[ 0.000000] Linux version 5.19.0-rc4 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Wed Aug 24 14:46:22 UTC 2022
[ 0.000000] random: crng init done
[ 0.000000] Machine model: Ventana VT1 QEMU
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10001
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] SBI SRST extension detected
[ 0.000000] earlycon: uart8250 at MMIO 0x0000000010000000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: EFI v2.90 by Das U-Boot
[ 0.000000] efi: RTPROP=0xfe73c020 SMBIOS=0xfe738000 MEMRESERVE=0xfd3ca020
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fe737fff]
[ 0.000000] node 0: [mem 0x00000000fe738000-0x00000000fe738fff]
[ 0.000000] node 0: [mem 0x00000000fe739000-0x00000000fe73bfff]
[ 0.000000] node 0: [mem 0x00000000fe73c000-0x00000000fe742fff]
[ 0.000000] node 0: [mem 0x00000000fe743000-0x00000000fff77fff]
[ 0.000000] node 0: [mem 0x00000000fff78000-0x00000000fff78fff]
[ 0.000000] node 0: [mem 0x00000000fff79000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000ffffffff]
[ 0.000000] SBI HSM extension detected
[ 0.000000] riscv: base ISA extensions acdfhim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] riscv: Svinval extension supported
[ 0.000000] percpu: Embedded 18 pages/cpu s34488 r8192 d31048 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/vda2 rootwait console=ttyS0 earlycon=uart8250,mmio,0x10000000
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] fixmap : 0xff1bfffffee00000 - 0xff1bffffff000000 (2048 kB)
[ 0.000000] pci io : 0xff1bffffff000000 - 0xff1c000000000000 ( 16 MB)
[ 0.000000] vmemmap : 0xff1c000000000000 - 0xff20000000000000 (1024 TB)
[ 0.000000] vmalloc : 0xff20000000000000 - 0xff60000000000000 (16384 TB)
[ 0.000000] lowmem : 0xff60000000000000 - 0xff60000080000000 (2048 MB)
[ 0.000000] kernel : 0xffffffff80000000 - 0xffffffffffffffff (2047 MB)
[ 0.000000] Memory: 2034884K/2097152K available (7677K kernel code, 4908K rwdata, 4096K rodata, 2204K init, 463K bss, 62268K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=16.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=16
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped using AIA
[ 0.000000] riscv-imsic: imsics@28000000: hart-index-bits: 4, guest-index-bits: 3
[ 0.000000] riscv-imsic: imsics@28000000: group-index-bits: 0, group-index-shift: 24
[ 0.000000] riscv-imsic: imsics@28000000: mapped 255 interrupts for 16 CPUs at 0x0000000028000000
[ 0.000000] riscv-imsic: imsics@28000000: enable/disable sync using interrupt 2
[ 0.000000] riscv-imsic: imsics@28000000: providing IPIs using interrupt 1
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [15]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000175] sched_clock: 64 bits at 10MHz, resolution 100ns, wraps every 4398046511100ns
[ 0.003481] Timer interrupt in S-mode is available via sstc extension
[ 0.025738] Console: colour dummy device 80x25
[ 0.029321] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=40000)
[ 0.031650] pid_max: default: 32768 minimum: 301
[ 0.034091] LSM: Security Framework initializing
[ 0.040644] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.041871] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.113999] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.115760] cblist_init_generic: Setting shift to 4 and lim to 1.
[ 0.118488] riscv: ELF compat mode supported
[ 0.118927] ASID allocator using 16 bits (65536 entries)
[ 0.122786] rcu: Hierarchical SRCU implementation.
[ 0.128655] Remapping and enabling EFI services.
[ 0.138132] smp: Bringing up secondary CPUs ...
[ 0.289674] smp: Brought up 1 node, 16 CPUs
[ 0.370978] devtmpfs: initialized
[ 0.384472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.385374] futex hash table entries: 4096 (order: 6, 262144 bytes, linear)
[ 0.395700] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.402142] audit: initializing netlink subsys (disabled)
[ 0.405233] audit: type=2000 audit(0.332:1): state=initialized audit_enabled=0 res=1
[ 0.409992] cpuidle: using governor menu
[ 0.991252] riscv-aplic d000000.aplic: 96 interrupts forwared to MSI base 0x0000000028000000
[ 1.023056] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 1.032106] ACPI: Interpreter disabled.
[ 1.032688] iommu: Default domain type: Translated
[ 1.033087] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.035341] SCSI subsystem initialized
[ 1.040840] usbcore: registered new interface driver usbfs
[ 1.041953] usbcore: registered new interface driver hub
[ 1.042680] usbcore: registered new device driver usb
[ 1.044787] Registered efivars operations
[ 1.066789] vgaarb: loaded
[ 1.070677] clocksource: Switched to clocksource riscv_clocksource
[ 1.074619] pnp: PnP ACPI: disabled
[ 1.116227] NET: Registered PF_INET protocol family
[ 1.126621] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.137534] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 1.138660] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.139011] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.139754] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 1.141266] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.144634] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.145365] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[ 1.148897] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.159051] RPC: Registered named UNIX socket transport module.
[ 1.159353] RPC: Registered udp transport module.
[ 1.159522] RPC: Registered tcp transport module.
[ 1.159699] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.176066] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.213547] NFS: Registering the id_resolver key type
[ 1.216026] Key type id_resolver registered
[ 1.216360] Key type id_legacy registered
[ 1.217343] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.217841] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 1.220266] 9p: Installing v9fs 9p2000 file system support
[ 1.224198] NET: Registered PF_ALG protocol family
[ 1.225340] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.227416] io scheduler mq-deadline registered
[ 1.227748] io scheduler kyber registered
[ 1.249381] pci-host-generic 30000000.pci: host bridge /soc/pci@30000000 ranges:
[ 1.251169] pci-host-generic 30000000.pci: IO 0x0003000000..0x000300ffff -> 0x0000000000
[ 1.252302] pci-host-generic 30000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
[ 1.252770] pci-host-generic 30000000.pci: MEM 0x0400000000..0x07ffffffff -> 0x0400000000
[ 1.254245] pci-host-generic 30000000.pci: Memory resource size exceeds max for 32 bits
[ 1.260809] pci-host-generic 30000000.pci: ECAM at [mem 0x30000000-0x3fffffff] for [bus 00-ff]
[ 1.264633] pci-host-generic 30000000.pci: PCI host bridge to bus 0000:00
[ 1.265205] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.265504] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.265799] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 1.266707] pci_bus 0000:00: root bus resource [mem 0x400000000-0x7ffffffff]
[ 1.268627] pci 0000:00:00.0: [1b36:0008] type 00 class 0x060000
[ 1.628806] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.648238] printk: console [ttyS0] disabled
[ 1.652252] 10000000.uart: ttyS0 at MMIO 0x10000000 (irq = 166, base_baud = 230400) is a 16550A
[ 1.656816] printk: console [ttyS0] enabled
[ 1.656816] printk: console [ttyS0] enabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.657728] printk: bootconsole [uart8250] disabled
[ 1.810913] loop: module loaded
[ 1.813333] virtio_blk virtio1: 1/0/0 default/read/poll queues
[ 1.825357] virtio_blk virtio1: [vda] 1071932 512-byte logical blocks (549 MB/523 MiB)
[ 1.909650] vda: vda1 vda2 vda3
[ 1.942916] tun: Universal TUN/TAP device driver, 1.6
[ 1.964238] e1000: Intel(R) PRO/1000 Network Driver
[ 1.964596] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.965214] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.965496] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.967174] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.967691] ehci-pci: EHCI PCI platform driver
[ 1.968378] ehci-platform: EHCI generic platform driver
[ 1.969031] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.969540] ohci-pci: OHCI PCI platform driver
[ 1.970742] ohci-platform: OHCI generic platform driver
[ 1.974710] usbcore: registered new interface driver uas
[ 1.975701] usbcore: registered new interface driver usb-storage
[ 1.979125] mousedev: PS/2 mouse device common for all mice
[ 1.985774] goldfish_rtc 101000.rtc: registered as rtc0
[ 1.987831] goldfish_rtc 101000.rtc: setting system clock to 2022-08-25T10:45:53 UTC (1661424353)
[ 1.993669] syscon-poweroff soc:poweroff: pm_power_off already claimed for sbi_srst_power_off
[ 1.995212] syscon-poweroff: probe of soc:poweroff failed with error -16
[ 1.998593] sdhci: Secure Digital Host Controller Interface driver
[ 1.998909] sdhci: Copyright(c) Pierre Ossman
[ 1.999509] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.001283] usbcore: registered new interface driver usbhid
[ 2.001588] usbhid: USB HID core driver
[ 2.002927] riscv-pmu-sbi: SBI PMU extension is available
[ 2.004257] riscv-pmu-sbi: 16 firmware and 18 hardware counters
[ 2.017615] NET: Registered PF_INET6 protocol family
[ 2.032397] Segment Routing with IPv6
[ 2.032878] In-situ OAM (IOAM) with IPv6
[ 2.033574] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.037639] NET: Registered PF_PACKET protocol family
[ 2.039420] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.040579] 8021q: 802.1Q VLAN Support v1.8
[ 2.043124] 9pnet: Installing 9P2000 support
[ 2.043788] Key type dns_resolver registered
[ 2.050694] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 2.145175] EXT4-fs (vda2): mounted filesystem with ordered data mode. Quota mode: disabled.
[ 2.146407] VFS: Mounted root (ext4 filesystem) readonly on device 254:2.
[ 2.150622] devtmpfs: mounted
[ 2.201842] Freeing unused kernel image (initmem) memory: 2204K
[ 2.228413] Run /sbin/init as init process
[ 2.242343] Run /etc/init as init process
[ 2.243725] Run /bin/init as init process
[ 2.244949] Run /bin/sh as init process
sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-5.1#
sh-5.1#
sh-5.1# QEMU: Terminated
Thank you.
Regards
Vaibhav Vivek Deshpande
|
|
|
