[yocto-autobuilder2][PATCH v2] README-Guide.md: Add multi-node content, extra config info
The instructions in README-Guide.md are a good starting point, but there
are some additional guidelines in this patch for setting up worker nodes
which may be useful to others who want to run their own Autobuilder
instance. Specifically, it adds:
- Section 1.3 on adding additional worker nodes to a cluster
- Section 1.4 on setting up an NFS share for the controller and workers
- A link to the Yocto Manual where the requirements to support running
builds on Ubuntu/Debian systems is listed
- A note to make sure that any new users (pokybuild3) created for the
Autobuilder have LANG set in their bash profile
Signed-off-by: Trevor Gamblin <email@example.com>
README-Guide.md | 108 +++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 106 insertions(+), 2 deletions(-)
diff --git a/README-Guide.md b/README-Guide.md
index 21dd7c1..832996f 100644
@@ -6,7 +6,8 @@ This guide will walk through how to install a stand-alone autobuilder controller
The final outputs of this section are a controller and worker installed in the same server, ready for trimming back to an individual organization's needs.
- > NOTE: The guide assumes that your host OS has the packages installed to support BitBake for the release(s) you are targeting. Please refer to the Yocto manual for those packages.
+ > NOTE: The guide assumes that your host OS has the packages installed to support BitBake for the release(s) you are targeting. Please refer to the Yocto manual for those packages:
The latest version of BuildBot is written in Python 3, so installation via pip3:
@@ -43,6 +44,14 @@ yocto-controller/yoctoabb
+Before proceeding, make sure that the following is added to the
+pokybuild3 user's exports (e.g. in .bashrc), or builds will fail after
Next, we need to update the `yocto-controller/yoctoabb/master.cfg` towards the bottom where the `title`, `titleURL`, and `buildbotURL` are all set. This is also where you would specify a different password for binding workers to the master.
Then, we need to update the `yocto-controller/yoctoabb/config.py` to include our worker. In that file, find the line where `workers` is set and add: ["example-worker"]. _NOTE:_ if your worker's name is different, use that here. Section 3.1 discusses how to further refine this list of workers.
@@ -61,7 +70,17 @@ Set `BASE_HOMEDIR` should be your build user's home directory. (There are she
> NOTE: The way the build step is written, the worker will pull a fresh copy of the helper from the server. Therefore these configuration files must be committed to the `yocto-autobuilder-helper` repo location you have specified in `yoctoabb/config.py` because the worker is given a build step that pulls from that repo (see `yoctoabb/builders.py`).
-Finally, as root, add the `yocto-*.service` files to `/lib/systemd/system` (See Appendix A). Run: `systemctl daemon-reload`. You should now be able to successfully start these services (e.g., `sudo systemctl start yocto-*`). The controller may take up to 15 seconds to start.
+Finally, it is time to start the Autobuilder. There are two ways to do this:
+1. As the pokybuild3 user, run the following:
+buildbot start yocto-controller
+buildbot-worker start yocto-worker
+2. As root, add the `yocto-*.service` files to `/lib/systemd/system` (See Appendix A). Run: `systemctl daemon-reload`. You should now be able to successfully start these services (e.g., `sudo systemctl start yocto-*`). The controller may take up to 15 seconds to start.
### 1.1) Configuring the Worker's Hash Equivalency Server
@@ -112,6 +131,91 @@ sudo /home/pokybuild3/yocto-worker/qemuarm/build/scripts/runqemu-gen-tapdevs \
In the above command, we assume the a build named qemuarm failed. The value of 8 is the number of tap interfaces to create on the worker.
+### 1.3) Adding Dedicated Worker Nodes
+Running both the controller and the worker together on a single machine
+can quickly result in long build times and an unresponsive web UI,
+especially if you plan on running any of the more comprehensive builders
+(e.g. a-full). Additional workers can be added to the cluster by
+following the steps in Section 1, except that the yocto-controller steps
+do not need to be repeated. For example, to add a new worker
+"ala-blade51" to an Autobuilder cluster with a yocto-controller at the
+IP address 188.8.131.52:
+1. On the yocto-controller host, add the name of the new worker to a worker
+list (or create a new one) e.g. 'workers_wrlx = ["ala-blade51"]' and
+make sure that it is added to the "workers" list.
+2. On the new worker node:
+useradd -m --system pokybuild3
+mkdir -p git/trash
+buildbot-worker create-worker -r --umask=0o22 yocto-worker 184.108.40.206 ala-blade51 pass
+chown -R pokybuild3:pokybuild3 /home/pokybuild3
+ > Note 1: The URL/IP given to the create-worker command must match the
+host running the yocto-controller.
+ > Note 2: The "pass" argument given to the create-worker command must
+match the common "worker_pass" variable set in yocto-controller/yoctoabb/config.py.
+3. Once you have finished with configuration, you can run the following
+and the worker should successfully join the cluster and become available
+to use with the builders, where "yocto-worker/" is the directory created
+in step 2:
+buildbot-worker start yocto-worker/
+### 1.4) Configuring NFS for the Autobuilder Cluster
+The Yocto Autobuilder relies on NFS to distribute a common sstate cache
+and other outputs between nodes. A similar configuration can be
+deployed by performing the steps given below, which were written for
+Ubuntu 18.04.In order for both the controller and worker nodes to be able
+to access the NFS share without issue, the "pokybuild3" user on all
+systems must have the same UID/GID, or sufficient permissions must be
+granted on the /srv/autobuilder path (or wherever you modified the config
+files to point to). The following instructions assume a controller node
+at 220.127.116.11 and a single worker node at 18.104.22.168, but
+additional worker nodes can be added as needed (see the previous
+1. On the NFS host:
+sudo apt install -y nfs-kernel-server
+sudo mkdir -p /srv/autobuilder/autobuilder.yoctoproject.org/
+sudo chown -R pokybuild3:pokybuild3 /srv/autobuilder/autobuilder.yoctoproject.org
+2. Add the following to /etc/exports, replacing the path and IP fields
+ as necessary for each client node:
+sudo systemctl restart nfs-kernel-server
+4. Adjust the firewall (if required). Example:
+sudo ufw allow from 22.214.171.124 to any port nfs
+5. On the client node(s):
+sudo apt-get install nfs-common
+sudo mount 126.96.36.199:/srv/autobuilder/autobuilder.yoctoproject.org/ /srv/autobuilder/autobuilder.yoctoproject.org/
## 2) Basics
This section is an overview of operation and a few basic configuration file relationships. See Section 3 for more detailed instructions.