Failed to create MTD partitions


JH
 

Hello Tom,

We have another issue to use Samsung NAND K9F2G08U0D-SCB0, I found a
similar issue posted in NXP community that NXP driver did not support
similar Samsung NAND
https://community.nxp.com/t5/i-MX-Processors/ECC-errors-with-Samsung-NAND-K9K8G08U0F-on-i-MX6UL/m-p/676885

We are using meta-freescale, does meta-freescale NXP driver support
Samsung K9F2G08U0D-SCB0? Or which version of the meta-freescale NXP
driver can support Samsung K9F2G08U0D-SCB0?

Thank you very much.

Kind regards,

Jupiter

On 5/29/21, Jupiter <jupiter.hce@gmail.com> wrote:
Hello,

There is another statement before the device found, is the Error
setting BCH geometry : -22 caused by ECC or by invalid JEDEC? It is
kernel version 4.19 on iMX6ULZ MCU.

[ 8.130891] nand: Could not find valid JEDEC parameter page; aborting
[ 8.137591] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[ 8.144246] nand: Samsung NAND 256MiB 3,3V 8-bit
[ 8.148995] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB
siz
e: 64
[ 8.158330] gpmi-nand 1806000.gpmi-nand: Error setting BCH geometry :
-22
[ 8.166690] gpmi-nand: probe of 1806000.gpmi-nand failed with error -22

Thank you.

Kind regards,

- jupiter


On 5/28/21, Jupiter <jupiter.hce@gmail.com> wrote:
Hello,

I am using MTD in kernel 4.19, I was able to run kernel boot to create
MTD partitions when I used NAND Winbond W29N02GV:

[ 7.961966] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xda
[ 7.968545] nand: Winbond W29N02GV
[ 7.972267] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048,
OOB
siz
e: 64
[ 7.986814] Bad block table found at page 131008, version 0x01
[ 7.994254] Bad block table found at page 130944, version 0x01
[ 8.002152] 3 cmdlinepart partitions found on MTD device gpmi-nand
[ 8.008479] Creating 3 MTD partitions on "gpmi-nand":
....................

Since we could not get Winbond W29N02GV supply anymore, we changed
Samsung NAND, Both are 3.3V 2Gib devices with the same memory
organization (2k pages +
64b OOB / 128k blocks) so these two parts should be equivalent in
terms of internal organization, but it failed to create MTD partitions
in kernel boot:

[ 8.137591] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[ 8.144246] nand: Samsung NAND 256MiB 3,3V 8-bit
[ 8.148995] nand: 256 MiB, SLC, erase size: 128 KiB, page size:
2048, OOB size: 64
[ 8.158330] gpmi-nand 1806000.gpmi-nand: Error setting BCH geometry :
-22
[ 8.166690] gpmi-nand: probe of 1806000.gpmi-nand failed with error
-22

Since it is a new board, I suspect one of following problem might
cause that error:

- HW
- MTD does not support Samsung?
- Need kernel configure?

Appreciate your comments and advice.

Thank you very much.

- jupiter