This bbappend depends on the virtualization-layer collection. Move it under the appropriate dynamic layer directory. Signed-off-by: Sean Anderson <sean.anderson@...> ---

Hi all, I just tried to build u-boot for machine p1020rdb with current master branches $ bitbake u-boot Loading cache: 100% |

Hi all, Where should patches for QorIQ components [1] go? I have some patches for meta-qoriq [2] and dce [3], but I can't figure out where to send them to. There is no mailing list in the READMEs,

The default GStreamer provided in iMX8 yocto only supports the command line it does not support GStreamer C code hence I need to cross-compile the GStreamer library for iMX8M Mini Yocto. I tried

ping? Is this the correct place to send patches for QorIQ components? I also have a patch for DCE [1] but I don't know where to send it. --Sean [1]

Hello, Em sex., 18 de fev. de 2022 às 06:43, Jan Claussen via lists.yoctoproject.org <claussen.j=eppendorf.de@...> escreveu: There are two BSP available in meta-freescale: -

I am a bit confused with the graphics support for the NXP BSP. It used to be Vivante, but with linux-fslc-imx it is Etnaviv although I thought it would be a linux-imx kernel with mainline patches. Is

Hi Otavio, The meta-qoriq layer on github [1] has not been updated since 2018. I cannot submit a patch against it because these patches would not apply. --Sean [1]

Please send a PR on GitHub. Em qui., 10 de fev. de 2022 às 18:42, Sean Anderson via lists.yoctoproject.org <sean.anderson=seco.com@...> escreveu: -- Otavio Salvador O.S.

Please send a PR on GitHub. Em qui., 10 de fev. de 2022 às 18:41, Sean Anderson via lists.yoctoproject.org <sean.anderson=seco.com@...> escreveu: -- Otavio Salvador O.S.

Hello, I'm using meta-freescale for my custom board and I have an issue with DisplayPort. I've flashed imx-boot with dp signed firmware + added dts changes but during boot I see in log: dmesg | grep

I forgot to note this in the subject, but these should be applied to meta-qoriq. --Sean

This bbappend depends on the virtualization-layer collection. Move it under the appropriate dynamic layer directory. Signed-off-by: Sean Anderson <sean.anderson@...> ---

This recipe depends on the freescale-distro collection. Move it to an appropriate dynamic layer. Signed-off-by: Sean Anderson <sean.anderson@...> --- conf/layer.conf

Hello Jan, On Thu, Jan 20, 2022 at 9:44 AM Jan Claussen via lists.yoctoproject.org <claussen.j=eppendorf.de@...> wrote: There are 3 points to be considered here, namely: 1) If

Hi, I am currently working on adding our custom patches to linux-fslc-imx on honister. Previously, we had patched linux-imx on Gatesgarth but there seems to have changed a lot. Seems like this kernel

Ok, understood. The RTL8822 driver available in the kernel is for PCI-only. You should push Realtek to upstream RTL8822CS SDIO support as working with an out-of-tree driver is too painful. I suggest

On Tue, Jan 11, 2022 at 10:06 AM Fabio Estevam via lists.yoctoproject.org <festevam=gmail.com@...> wrote: Ah, the driver is available at

Hi Benson, Looking at your log, I see you use an rtl8822 Wifi device, which is not supported in the mainline kernel. I assume you use an out-of-tree driver, right? When using out-of-tree drivers,

Hello, Em ter., 11 de jan. de 2022 às 07:08, <benson_young@...> escreveu: You'll need to compare the branches and see if it has been fixed in a newer kernel release. -- Otavio Salvador