Hi, Bottom line up front, built fsl-community-bsp dunfell for imx8mmevk and Linux 5.4 kernel hangs on boot. So far I've been NXP official releases. I really needed the 5.4 kernel so was excited when

Hi all, I'm working on a custom board based on IMX8MM. My RAM calibration tool works only with u-boot 2018.03 to 2018.04, and I already have a u-boot recipe with all the patches necessary. In sumo

Does your local.conf point to the right MACHINE? Also check your recipes-bsp/conf/layer.conf. Marc

Hello, I'm trying to fix and add some variables to my recipes-bsp/conf/machine/imx8mmdddr3lval.conf file, like editing MACHINE_FEATURES , and SERIAL_CONSOLES . I already have a separate layer that

Hello Sebastian Most of the cases it getting failed in post install intercept. Those errors are suspicious, Try to install the patch into poky layer and rebuild the Image. Thanks & Regards, Mathanraj

Hello, I am not sure if this is the right place to ask this, so I would be very grateful if you could point me in the right direction, if not… I have a custom board which uses the TXUL-8013

Hi, working with dunfell branch and I want to build image for i.Mx8M Nano EVK and using u-boot-fslc as bootloader. I have this setup in my conf/auto.conf:

Hola, Acabo de firmar la petición de "Todos: Paz mundial" y me encantaría que me ayudaras sumando tu firma. Nuestro objetivo es llegar a 100 firmas y necesitamos más apoyo. Para obtener más

Hello, I am a little bit new to yocto, I am looking for some help/reference link for simple-card driver integration for FM tuner chip to get audio data to the iMX8m-mini board through the I2S

Hi, I have a following statement to remove a node in a DTS file: &gpmi { /delete-node/ fsl,use-minimum-ecc; }; I can build it correctly in OpenWRT build, but I cannot built it correctly in OE /

Hello, Please refer to LSDK document – Chapter 5 bootloader which include some detailed information about TF-A and u-boot. You can also submit question to NXP community.

hello all, I am trying to boot ls1043a without optee. I managed to compile and run atf until it jumps to uboot. There i do not get any serial output anymore. INFO: Loading image id=5 at address

It is not. Please open a issue. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854

Hi, when I generate a SDK (for example by running MACHINE=imx8mmevk bitbake -c populate_sdk core-image-weston), I notice that the headers from linux-imx-headers are missing even though

Hi Team, We are using a Custom imx28-evk based board with the latest iMX yocto images (Zeus) ported into it. Linux version 5.4.20-fslc+g18d5e274c780. The problem is when the board boots up we keep on

I have an Opal 5 SOM and DevKit which is based on the i.MX53 ARD reference design, and am trying to get it to boot via the SD card. I'm using Yocto 3.1 (Dunfell) and meta-freescale (current). My

Hi, I want to use fw_printenv/setenv utilities on iMX6ULL Linux, the u-boot version is different between meta-freescale and oe-core, meta-freescale uses u-boot-imx_2018.03.bb

OK, thank you for your reply. Best regards Lei

Sure, it would be helpful if you can submit the patch. Best Regards, Zhenhua

Hi, So, may I backport this patch to linux-qoriq_5.4.bb and send a PR? Best regards Lei Maohui